MacroSystem Digital Video HDV-Recorder Manual do Utilizador descarregar pdf (Página 8)

Chapter 2

system runs a current version, you can start editing directly. If

the version number of the CD/DVD is higher, then you should

install the more recent version.

You must carry out the installation procedure if you do not see

the Main Menu screen once your system is turned on.

2.3.1 Installing from CD/DVD

Bogart SE is always installed from a CD. There is no other way

to install this software. The process is controlled using the

trackball/mouse or the keyboard. The installation procedure

can be monitored on a monitor, connected via VGA, DVI, HDMI

or SCART, depending on the last selected monitor (when using

a new hard-drive, VGA). It should be possible to switch from

one monitor to the other by pressing the v-key of a USB key-

board or on the screen.

Press the v-key repeatedly until your monitor displays the

menu. At the same time, the installation menu is always dis-

played via VGA. There are two methods of installing Bogart SE,

either as a full installation or as an update. Follow these steps

to install: The CD/DVD used to install Bogart SE is a boot me-

dium. This means that this installation cannot be started from

the ‘Install product’ menu, but instead by inserting the medium

in the drive and restarting the editor (starting a system is often

called ‘booting’). In order to do this, the CD must be inserted in

the CD/DVD unit before the system is booted.

Inserting the CD in devices without buttons on the front (Ultra

upgrade and Laptop):

To insert the CD/DVD, power up the editor. As soon as the

indicator light of your DVD unit lights up, you should press the

eject button of the unit, insert the CD and close the drawer.

Inserting the CD in devices without buttons on the front (Ultra

upgrade and Laptop):

If your device is already pre-installed with a system software,

please wait until it has fully powered up and is ready for opera-

tion. Open the CD/ DVD tray using the eject button on the front

panel of the editor. For an `empty´ system without any system

software (if you are using a new hard-drive for instance), the in-

stallation is a little different: Power up the device and press the

eject button a few times. The tray will open and the installation

medium can be inserted. Now close the tray using the eject

button. In some cases, the tray may re-open. Simply power

down the editor if this is the case. To do this, you should press

the OK and ON/OFF buttons (on the front) simultaneously for

about 4 seconds. The main switch, described in the hardware

manual, can also be used. The system will now switch off.

Now restart the device. The editor will now boot from the CD/

DVD and on-screen instructions will be displayed for complet-

ing the installation.

Please follow the instructions for the installation. In order to

select options, just click with the trackball (or the mouse) on

the function (or the symbol that represents it) or press the key

corresponding to the option on the keyboard.

Depending on the conﬁguration of your device, you can

choose to send screen output for the installation via SCART,

Video, HDMI or DVI. This is only possible in the ﬁrst few menus

and only makes sense right here. If you do not see a picture af-

ter the installation, the screen output may have been switched

to an unused screen. In that case, you should press the v-key

on your connected USB keyboard or click the menu option

with the mouse pointer in order to direct the video output to

a different output. Before the installation can be started, your

hardware is analyzed and, if necessary, adjustments are made.

The installation begins with a language selection: English or

German. This menu also allows you to switch between HDMI,

DVI and/or SCART. When you have selected the language,

you will see a warning text telling you that you must have the

activation code for Bogart SE 5, in order to be able to enter it

after the installation. If you do have the necessary activation

code, you can continue with the installation. If you do not have

the activation code, you should abort this installation.

Note: the activation code for Bogart SE 5 is not entered during

the installation, but will only be required after starting Bogart

SE 5. If you do not enter an activation code for Bogart SE 5,

you will not be able to use the system any further and it will

automatically switch off.

Without a prior installed Bogart SE system software, only a full

installation will be possible. With a previous Bogart SE

installation already on the hard-drive, the installation will au-

tomatically offer to proceed with an update. If you wish to go

ahead with a full installation instead, use the front buttons

to make the change . Once you have decided on the

installation type, the installation will begin. In the meantime, a

progress bar will be shown. During that time, no other entry is

possible.

When done, you will be informed if the installation was suc-

cessful. In any case, the DVD tray will open automatically and

you will be asked to remove the medium. Press the OK key to

close the tray and end the installation. The installation is now

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 111 112

Comentários a estes Manuais

Sem comentários

MacroSystem Digital Video HDV-Recorder Manual do Utilizador Página 8

Comentários a estes Manuais

Manuais e produtos relacionados com Gravadores de vídeo digitais (DVR) MacroSystem Digital Video HDV-Recorder